Johns Manville Blown-In Insulation Nationwide | Walt’s Insulation

Johns Manville Blown-In Insulation in West Hollywood: What to Know First

Johns Manville blown-in insulation in West Hollywood typically costs between $1,800 and $4,200 for a full attic in a standard 1,200 to 1,800 square foot home here, and most jobs are completed in a single day. We’re an independent Johns Manville service provider, not an authorized dealer, which means we can give you straight answers about what’s working, what isn’t, and what actually needs replacing. If you own a West Hollywood home and you’re wondering whether the Johns Manville insulation in your attic or walls is doing its job, call us at (213) 527-4062. Walt Brenner and our crew have been working on Johns Manville blown-in jobs across West Hollywood since 2000, and we’ve seen every way insulation ages, settles, and fails in this climate.

Call (213) 527-4062

How Johns Manville Products Fail - and How We Fix Them

Johns Manville makes solid blown-in insulation, but nothing lasts forever, especially in West Hollywood where older buildings, coastal air, and decades of deferred maintenance collide. Here’s what we actually find when we open up attics and walls around here.

• Climate Pro and Attic Protector settling below stated R-value. Johns Manville’s Climate Pro loose-fill fiberglass and Attic Protector blown-in fiberglass are decent products, but they settle over time, especially when installed over existing batts or in deeply sloped attics common in older West Hollywood hillside homes. We regularly measure attics that were “R-38 on paper” reading R-19 or worse. Our fix is a measured removal or a blown-in top-up to a verified depth, not just eyeballing it.
• Spider custom-blown fiberglass with uneven density pockets. Johns Manville Spider insulation is blown into open wall cavities before drywall goes up, but we’ve found uneven fill in plenty of West Hollywood remodels, particularly in older stucco buildings near Santa Monica Boulevard where walls were retrofitted in the 1990s. The symptom is simple: rooms that never hold temperature, even with the HVAC running. We dense-pack the cavities properly from the interior or exterior, a repair most crews won’t touch because it’s slow work.
• Cellulose products retaining moisture in flat-roof buildings. West Hollywood has a lot of flat and low-slope roofs, and when those roofs leak even slightly, Johns Manville cellulose blown-in insulation wicks moisture and compacts. Homeowners tell us the ceiling feels damp or they smell something musty but can’t find the source. Once we pull the wet insulation, we always air seal and check the roof deck before reinstalling.
• Missing top-up over original 1970s rock wool or fiberglass batts. Many West Hollywood homes built between the 1950s and 1980s have original rock wool or thin fiberglass batts with a light layer of Johns Manville product blown on top years later. The problem is the old layer is doing nothing, and the Johns Manville layer was never thick enough. A proper top-up with Climate Pro blown-in fiberglass to current code depth fixes it, but only if we remove the worst of the old material first.
• Air leaks defeating good insulation. This is the one we see most in West Hollywood. Johns Manville insulation can be installed perfectly, but if the attic floor has unsealed penetrations around can lights, plumbing stacks, and top plates, the insulation can’t do its job. The symptom is a house that’s cold in winter and hot in summer no matter the thermostat setting. We air seal before we insulate, every time, because blowing new material over leaky framing is just wasting money.

Our Johns Manville Blown-In Insulation Process

Here’s how a Johns Manville blown-in job goes when you call Walt’s Insulation.

1. 1
   You call and a live person answers. That’s usually Walt himself or one of our office staff. We ask about your home, your comfort complaints, and what you know about the existing insulation.
2. 2
   We measure and diagnose before we quote anything. We check attic depth, look for settling, moisture, and air leaks, and we give you an upfront price based on actual square footage and target R-value. No vague estimates.
3. 3
   We decide what stays and what goes. If your Johns Manville material is dry and reasonably distributed, we may top it up. If it’s compacted, wet, or rodent-damaged, we remove it and start fresh.
4. 4
   We air seal, then blow the insulation. We seal top plates, wire penetrations, can light housings, and flue gaps. Then we blow Johns Manville Climate Pro or Attic Protector to verified depth, using cards marked to the exact R-value tier.
5. 5
   We test and show you the work. We take photos of the finished attic, confirm depths in multiple spots, and walk you through what we did.
6. 6
   We leave and it’s done. The Done Right Promise covers the workmanship for life. If it’s not right, we come back and make it right.

What Johns Manville Blown-In Insulation Costs in West Hollywood

Blown-in insulation pricing in West Hollywood depends on square footage, existing material, access difficulty, and whether removal is needed. Based on jobs we’ve done across the 90046 and 90069 ZIP codes, here’s what homeowners can expect.

• Attic top-up (existing Johns Manville material, no removal): $1,200 to $2,400 for a typical 1,200 to 1,500 sq ft attic
• Full attic removal and new Johns Manville blown-in: $2,800 to $4,200, depending on depth and debris
• Dense-pack wall insulation (Johns Manville Spider or fiberglass): $2,500 to $5,500 for an average West Hollywood home, varies with wall count and access
• Blown-in top-up only on an existing crawl or small attic: $800 to $1,500

What moves the price: whether we remove old material, how accessible the attic is, whether we have to cut access hatches, and whether there’s rodent damage to clean up. Call (213) 527-4062 for a free estimate, and ask about the no-trip-charge policy in our county. We also give a free second opinion on any written estimate, so if another company quoted you, bring it in.

Why West Hollywood Homeowners Call Walt’s Insulation for Johns Manville Work

We’re the one down the road, and we’ve been doing this since 2000. Walt Brenner grew up in San Antonio, learned the trade there, and has been working West Hollywood attics and walls for years, including plenty of older buildings near Santa Monica Boulevard where the insulation was, to put it charitably, an afterthought. Our techs are background-checked and uniformed, so you know who’s in your house. We install Johns Manville products because they’re solid materials, and we also work with Owens Corning, Knauf, CertainTeed, Rockwool, and others, including Reflectix for radiant barrier applications, so nobody’s steering you toward whatever’s on the truck. The Done Right Promise is lifetime workmanship: if we don’t do it right, we make it right. No runaround.

FAQs